windows install fatal error.....

Triple6_wild · Post by **Triple6_wild** » Sun Jan 16, 2005 5:28 pm

GA~
I'm attempting to install windows xp onto a formated harddrive and half way through the install I get the error "One of the components that windows needs to continue setup could not be installed" the computer then resets and the same thing happens again,its an endless chain of fatal errors. Anyone got any ideas?

666~
GA didnt wanna post him self so can ya help him out guys

Archived topic from Iceteks, old topic ID:3024, old post ID:24865

Red Squirrel · Post by **Red Squirrel** » Sun Jan 16, 2005 6:07 pm

Try a memtest, sounds like bad ram. I had a similar issue, but in my case no errors, it would just reboot, turned out the stick of ram had millions of errors on it.

Archived topic from Iceteks, old topic ID:3024, old post ID:24866

Triple6_wild · Post by **Triple6_wild** » Sun Jan 16, 2005 6:46 pm

ok he replaced the ram and still no luck

any other ideas?

Archived topic from Iceteks, old topic ID:3024, old post ID:24867

Chris Vogel · Post by **Chris Vogel** » Sun Jan 16, 2005 7:33 pm

Microsoft suggests a damaged installation disc. Does it look damaged?

Archived topic from Iceteks, old topic ID:3024, old post ID:24869

Triple6_wild · Post by **Triple6_wild** » Sun Jan 16, 2005 7:51 pm

GA says it doesnt look damaged and he said its the 2nd disc he tryed

Archived topic from Iceteks, old topic ID:3024, old post ID:24870

Red Squirrel · Post by **Red Squirrel** » Sun Jan 16, 2005 8:15 pm

bad cd-rom drive maybe? I've had this happen to me once.

Archived topic from Iceteks, old topic ID:3024, old post ID:24871

Death · Post by **Death** » Sun Jan 16, 2005 8:57 pm

What kind of system is windows XP going to be put on? Does it meet all the specifications? You might have less of something than windows XP requires. That's the only thing I can think of. Either that, or the install is a hacked copy that has errors on it. Did the hard drive format successfully? I would test it out to make sure that it's in working condition, or better yet, if you have a spare hard drive laying around, I would try that one to see if the install proceeds.

Archived topic from Iceteks, old topic ID:3024, old post ID:24875

Red Squirrel · Post by **Red Squirrel** » Sun Jan 16, 2005 9:23 pm

Yeah forgot to mention that, did you test the drive for bad clusters? I've seen this a few times where a system won't even boot because of bad clusters. Most likely the system was moved while it was on. So many people do that...

Archived topic from Iceteks, old topic ID:3024, old post ID:24876

rovingcowboy · Post by **rovingcowboy** » Sun Jan 16, 2005 9:55 pm

sounds like your trying to put it on too small of a harddrive to me.

or the motherboard wont work with xp or the ram is not fast enough.

check out the requirements for the xp system and see if they are all met or if there is any chance that one requirement is too close to the lower end.

also it could be a pirate copy of xp your trying to install and the componet is the file on the orignal own's hard drive that the xp system needs.? that sometimes happens when the xp systems where bought as preinstalled.

you can always take it to the repair shop and have it check to see if it meets xp requirements.

the bad sectors on the hard drive wont stop an install unless the whole hard drive is bad. or just enough of it to not have enough room for xp.

xp takes a minimum of 196 mbs of ram why ? because xp use's ram for the recourse's and it also takes 150 mbs justs for the xp system it's self.

so to do any work on xp like photo shop you need a minimum of 512 mbs of rdram. if your mother board can handle it put on 1gb of ram.

also your hard drive might be too small. check that out.

thats all i can think of for now

good luck.

Archived topic from Iceteks, old topic ID:3024, old post ID:24881

Triple6_wild · Post by **Triple6_wild** » Sun Jan 16, 2005 10:12 pm

aight hes gonna check for bad clusters so i will be back sooner or latter to let ya know how it works out

Archived topic from Iceteks, old topic ID:3024, old post ID:24883

Nathan · Post by **Nathan** » Mon Jan 17, 2005 6:39 am

Sue them all.

Archived topic from Iceteks, old topic ID:3024, old post ID:24889

richardj · Post by **richardj** » Mon Jan 17, 2005 10:51 pm

My XP Pro installed before always with no problem. This time, it just froze up with no error messages about a hundred times.

Finnaly, I disabled everything in the CMOS that I could (plug & play, network, modem exct.) then it went in right away.

I would try this, clean the cd & buy a cd player cleaner, its a cd with little brushes on it.

You can also try returning your CMOS to it's default by going into it & pressing F6, or hold down F6 as it boots.

Archived topic from Iceteks, old topic ID:3024, old post ID:24901

rip_phreaker · Post by **rip_phreaker** » Thu May 05, 2005 11:38 pm

best solution, download and install some kind of linux... no more computer problems

Archived topic from Iceteks, old topic ID:3024, old post ID:26663